homelite028
ArboristSite Operative
needing xl-925 super ring set
i am in need set of rings for my homelite xl-925 super
i am in need set of rings for my homelite xl-925 super
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
Still lookin'
I got a twelve foot aluminum pipe wif a remington mity mite strapped to end of it. Apparently it works quite well.
Trade for a P-52.:msp_rolleyes:
Anthony_Va.
XPW Fan Club
I need to find a new or very good used 075 cylinder/piston.
Stihl 26 to trade...
Hello all, I bought a Stihl 26 of Ebay prolly 3 or 4 years ago now. Used it to cut 6-8 cords of wood when it became hard to keep it running. From the advice I've received on here and trouble shooting it sounds like it has an air leak. Anyways the point is that I've been given a new saw since and bought another one so my interest in taking this one apart is waning a bit, I thought I'd see if anyone on here would wanna partial trade it for a mini-mill or small chainsaw mill they aren't using? Not looking for anything real fancy just something i can use to do like 12-14 inch logs to learn a bit about it.
Hello all, I bought a Stihl 26 of Ebay prolly 3 or 4 years ago now. Used it to cut 6-8 cords of wood when it became hard to keep it running. From the advice I've received on here and trouble shooting it sounds like it has an air leak. Anyways the point is that I've been given a new saw since and bought another one so my interest in taking this one apart is waning a bit, I thought I'd see if anyone on here would wanna partial trade it for a mini-mill or small chainsaw mill they aren't using? Not looking for anything real fancy just something i can use to do like 12-14 inch logs to learn a bit about it.
SawGarage
Addicted to ArboristSite
I'm back from vacation and tired.......I'll rest up by building a few saws.
I need some 028 bits. The trigger cover, presence lever, throttle rod, a brake cover......
I have an extra super I'm parting out so if y'all need anything.........
I also have a tired looking but good running 266xp I want to trade off.....
SHHTUFF I could use:
BLA BLA BLA BLA BLA BLA....
oh , AND -- LOTS of other parts that are rattling around upstairs...
THAT'S IT!!! :bang: I KNEW there was something else!! i need the handle/throttle cover, screw and presence lever for a METAL tank 028, and a side-bolted muffler
But, Randy, you's 1st
I have the brake cover for you
BTW
I've never worked on one, so not sure.
371 would be but not sure on the 272.
I'm assuming the 371K clutch is the same.I have an oil pump, clutch cover (new) (ya don't need a clutch?
PM me with what you've got and what you need for it. Thanks for the replys.
Last edited:
Dan_IN_MN
Addicted to ArboristSite
Homelite 2000 decomp part needed
Hello
I need a part for a Homelite 2000. The decomp lever has two spring clips to hold it in the decomp position. I need the lower clip. P/N 65755 Anyone have an extra one?
Hello
I need a part for a Homelite 2000. The decomp lever has two spring clips to hold it in the decomp position. I need the lower clip. P/N 65755 Anyone have an extra one?
thomas1
sodium pentothal
I have both ends of a HT75. All you would need to get is the shaft. They are still available from Stihl, only $400. :dribble:
Think I would have to pass on that. LOL :waaaht: I would be happy with a cheap-O :hmm3grin2orange: Won't get used enough. Thanks!
ptjeep
Addicted to ArboristSite
Bump
Cylinder and air filter covers
HD air filter
Air filter elbow
Oil pump
Worm gear
Clutch drum & bearing
Clutch cover
Chainbrake parts found. Still need the above.
HD air filter
Air filter elbow
Oil pump
Worm gear
Clutch drum & bearing
Clutch cover
Chainbrake parts found. Still need the above.
Last edited:
I got one that I could trade.
Looking for something big, old with a bow bar on it.
And by the way, thats a big old saw, not a big old woman.
I got one that I could trade.
Looking for something big, old with a bow bar on it.
And by the way, thats a big old saw, not a big old woman.
:hmm3grin2orange: Thanks Mark,but I don't need one that bad. I like that big old saw,even got an extra bar and 3 chains for it ! LOL Anything else you might like?
I'll have to think about that. :msp_tongue:
I might have some good plastics. You need the decomp hole?
