Swap meet...

[redray46]

Still looking :msp_angry:

Is it poly or aluminum?I just picked up a box of Stihl parts,saw a couple of flywheels in it,I will check tomorrow.

 

[lwn9186]

Is it poly or aluminum?I just picked up a box of Stihl parts,saw a couple of flywheels in it,I will check tomorrow.

Its aluminum, I have one on the way. Thanks

 

[tlandrum]

i am in need of a presence lever for a 394xp

still need this

 

[Madsaw]

still need this

Terry,
I am not famialar with that term. What our where is that lever?
Bob

 

[Jacob J.]

Terry,
I am not famialar with that term. What our where is that lever?
Bob

It's the throttle trigger interlock, that pops up out of the back of the pistol grip. It's a $3.35 part at a dealer.

 

[Madsaw]

It's the throttle trigger interlock, that pops up out of the back of the pistol grip. It's a $3.35 part at a dealer.

Thanks for the info JJ.
Did you get my PM about the IEL the other day?
Bob

 

[Jacob J.]

Thanks for the info JJ.
Did you get my PM about the IEL the other day?
Bob

Nope...are you telling me you have an IEL model K under the woodpile?

 

[Madsaw]

Nope...are you telling me you have an IEL model K under the woodpile?

LOL
I wish, I would hand deliver that though. Naw I got a Hb here. I also did get the one other 2 man we talked about too. I am going to send the merc bar the craftsman bar and the other one together. The 3 should wrap up together nicely. I am really going to keep a good look out for you on some of them older IELs around here too.
Bob

 

[Jordan3605]

Looking for Pro Mac 510 parts!
trying to complete a project craigslist find
-Handle Assembly
-Throttle Trigger Assembly

--Or if anyone has a complete 510 with a scored piston/cylinder, that would work fine.

not much for trade to offer , but have Paypal+cash
Best way to reach would be a Private Message
Thanks

 

[Jacob J.]

LOL
I wish, I would hand deliver that though. Naw I got a Hb here. I also did get the one other 2 man we talked about too. I am going to send the merc bar the craftsman bar and the other one together. The 3 should wrap up together nicely. I am really going to keep a good look out for you on some of them older IELs around here too.
Bob

Sounds goodly. I'm down for the HB so now the 395 definitely has your name on it.

 

[SawGarage]

It's the throttle trigger interlock, that pops up out of the back of the pistol grip. It's a $3.35 part at a dealer.

:jester::hmm3grin2orange:

 

[67L36Driver]

Poulan 361, 400, 450 recoil starter disc needed.

Poulan part #4264, large plastic washer goes between the spring and pulley. Tends to keep the spring anchor loop on its' knob.

I shouldn't have cleaned it.:msp_unsure: The crap was keeping it together.

misc. parts or a dead president.

 

[7hpjim]

I need a bunch of stuff for the Poulan Pro 525/Pioneer P52, easier for you to tell me what ya got than for me to list, got green for trade, also air filter and filter cover for :msp_scared:stihl 045, pm me.Thanks Jim

 

[firefighter33]

Sounds goodly. I'm down for the HB so now the 395 definitely has your name on it.

u still got one left for me right JJ?

 

[surfincr]

looking for 2 oil seals for the clutch side of an 045. as well as the needle bearing for the clutch or will take the entire assembly.

have green or a craftsman 2.1 to trade

 

[jimbo1490]

looking for 2 oil seals for the clutch side of an 045. as well as the needle bearing for the clutch or will take the entire assembly.

have green or a craftsman 2.1 to trade

Do you know the size of the seals? Most older Stihls take standard off-the-shelf seals. State the size in mm, I.D. X O.D. x width, and I'll look it up for you and tell you if it's standard seal or not.

Jimbo

 

[surfincr]

Do you know the size of the seals? Most older Stihls take standard off-the-shelf seals. State the size in mm, I.D. X O.D. x width, and I'll look it up for you and tell you if it's standard seal or not.

Jimbo

i'll see if i cant get the measurements when i get home. it may be tough to get the exact size though since the seal split on me when i pulled it out from being so brittle.

 

[SawGarage]

i'll see if i cant get the measurements when i get home. it may be tough to get the exact size though since the seal split on me when i pulled it out from being so brittle.

measure the crank, and the metal rim on the seal..as well as the width of the metal piece.

J

 

[67L36Driver]

i'll see if i cant get the measurements when i get home. it may be tough to get the exact size though since the seal split on me when i pulled it out from being so brittle.

You should measure the housing bore, the shaft diameter and the thicknes of the shell of the seal. Single lip or double lip.

 

[sachsmo]

Wanted, needed, Dolmar 6800i or 6000i clutch cover.


PM me,

Thanks

mo