Swap meet...

[dh1984]

dang!!!! Any body want a nice mac 2-10 with good compression, needs a carb kit

LOL how much or what you want in trade

 

[bplust]

Can anyone ID these most likely Homelite clutches?

(most likely, based on the fact that they came in a bucket of parts that have all been Homelite so far)

View attachment 228851

 

[jnl502]

I heard that carb was discontinued/recalled 30 years ago. I think Bob Johnson told me that.

This is what you want:
Chainsawr mcculloch mac 1-10, 2-10, 10-10 chainsaw walbro sdc carb conversion kit

that explanes alot. have never figured out why a family aireloom 2-10 has 2 idle adjustment screws and the hi/lo screws don't line up even close to outside holes. I have to remove the cover and airfilter and it still hard to adjust:censored:
jnl

 

[fastLeo151]

LOL how much or what you want in trade

Got any 044 stuff?

 

[fastLeo151]

Anyone interested in an 044?

It's missing some parts, the recoil, clutch drum, carb, and has a scored piston. I have an extra cylinder that came off a saw with a scored piston, they may clean up.

I haven't done an inventory of what all it is missing, but those are the major parts so far.

I also have a nice little Husky 50

Looking to trade for other saws, preferably runners, but wouldn't mind stuff that needs a little work.

Chris

I like the 044, what do you need for it?

 

[Duke Thieroff]

Ok, so you wont take cash, how bout a MAC 3-25? that needs just a little work.

No thanks my man, you can try posting for the parts you need in the Old Mag Swap Meet. Someone may be able to accomodate you.

Chris im gonna take that saw off your hands just so I can stop seein it on here!! Haha

Good luck, buckaroo!

Chris

 

[DSS]

What about lint that is stuck to my ass hair? Does that count? I could knit a full sweater from one harvest!!

Really though, that is pretty ####ing nasty.

 

[Warped5]

Giving this a shot .... got a guy over here that needs to replace the 20" bar on his Mac 10-10A. It's his primary firewood saw .. anyone got a decent used one? Have some $ to trade, please PM me ... thanks!

 

[tbone75]

Really though, that is pretty ####ing nasty.

Yep.....Even worse than a hairy neeked midget! :msp_scared:

 

[dh1984]

Giving this a shot .... got a guy over here that needs to replace the 20" bar on his 10-10A. It's his primary firewood saw .. anyone got a decent used one? Have some $ to trade, please PM me ... thanks!

PM sent

 

[dh1984]

Got any 044 stuff?

no i sure don't but i got a lot of small poulan and homelite stuff though

i haven't had a chance to get my hand s on one yet unless i'm working on it for a freind or something.

 

[fastLeo151]

Heres a bit o everything

Stihl ms 250 c-be runs great

Poulan xxv 150+ psi runs good 16in bar and chain

Mcculloch 2-10 150 psi good spark but needs carb kit. 20in mac bar and chain( I think original)

Im looking for big stihl stuff, or a lil bit o cheeseView attachment 228905View attachment 228906View attachment 228907View attachment 228908View attachment 228909

 

[cat-face timber]

i am in need of some husky 235 parts, or a parts saw.
Anybody have one they can pull parts off of for me?
I need some fastners, and the choke linkage

bump

 

[thomas1]

HHmmm,,i got a 41 i think it needs some parts.
hows the P&C ??

P/C look good through the exhaust port. I couldn't get a good pic though.

Let me know if you want it.

 

[mdavlee]

Alright I'm going to put the 2153 on the chopping block with the 555. I would like to trade it towards a 365 or 372 x torq. It has 2 tanks through it and is basically brand new. I have a 16", 18", or 20" 3/8" .050" bars and chains available. I do like green paper also. I can get some pictures in here or pm me for some.

 

[Duke Thieroff]

Here is a couple of better pics and a vid of that little Husky 50 I'm looking to trade for bigger saws/projects.

This vid is some seriously old dried up locust.

Bump

 

[rms61moparman]

Bump

How would you trade on a GREAT Super 1050 Homolite>??????


Mike

 

[timberdollars]

Mcculloch 840

Came across a Mcculloch 840, been sitting and looks rough, wasn't seized and I torn it all apart to see a Kart engine internals. All looks good. No front handle bar and its mount is about half gone, would needed welded or just as parts.
Third intake ports!!!!!!!
Kart engine knock off.
recoil even worked
gear drive with sprocket still there.
carb's primer shoots out "SOMETHING" water or fuel? but does work.
Fuel tank is not corroded

ALSO HAVE ROUGH M47 and 2-10

Trades for Pioneer stuff or ? be aware heavy shipping on these parts

Pm me

Duane

 

[forestryworks]

Looking for a Mahle 046 p&c.

 

[roncoinc]

P/C look good through the exhaust port. I couldn't get a good pic though.

Let me know if you want it.

Well,,i went and looked and i cant find the danged saw anymore !! LOL !!
so i guess i dont need it