Swap meet...

[Modifiedmark]

I need a rear handle insert 503427502 for a Poulan Pro 505 or Jonsered 2077 or 2083. They are the same as about 50 husky models, but this one needs to be black. The Husky ones are all orange. Dealer says it is NLA. Just trying to clean up loose ends on my "new" 505.

Thats bunk or they just went NLA in the last couple weeks. I just got 2 of them myself that the dealer ordered. Same part number as well.

 

[Stihlofadeal64]

I know where there are a couple of 029 parts saws. PM if interested.

PM sent....

 

[surfincr]

i have a homelite super 2 that i am parting out. if anyone wants any of the parts let me know the parts are free just asking for shipping

 

[jeffro]

Need a 16mm sprocket and bearing for Stihl 036

Got a super low hour 036 that has the original smaller sprocket bearing. I think I can reuse the washer and E clip.

I want to put the larger size on. I need the clutch drum with the 16mm hole, the 16mm bearing, and a 3/8 - 7 rim sprocket to fit the newer clutch drum. I know the bearing is part# 9512 933 2380, unsure about the other bits.

For trade, I have the original smaller size bearing, etc if anyone is interested in that size (they are like new, the saw literally has only been used enough to need the original chain sharpened a time or two). Also, I have the Stihl plastic case that came with the saw, including scabbord, file, wrench (case is a little dusty and has some bar oil spilled in the bottom, but can clean up great) if anyone uses cases. I can come up with green backs if needed.

Also, got an older 041 farmboss (not AV) that I am considering parting out. Just putting a feeler out on this one.

 

[2000ssm6]

Looking for a Stihl 039/390 p&c in good condition.
thanks

 

[Stihlofadeal64]

I know where there are a couple of 029 parts saws. PM if interested.

Bump-- Where O where are you 2 nite, why did you leave me here all alone.....Still waiting on pics. Thanks

 

[fredmc]

Bump-- Where O where are you 2 nite, why did you leave me here all alone.....Still waiting on pics. Thanks

got busy -ain't been there yet

 

[fredmc]

Got a super low hour 036 that has the original smaller sprocket bearing. I think I can reuse the washer and E clip.

I want to put the larger size on. I need the clutch drum with the 16mm hole, the 16mm bearing, and a 3/8 - 7 rim sprocket to fit the newer clutch drum. I know the bearing is part# 9512 933 2380, unsure about the other bits.

For trade, I have the original smaller size bearing, etc if anyone is interested in that size (they are like new, the saw literally has only been used enough to need the original chain sharpened a time or two). Also, I have the Stihl plastic case that came with the saw, including scabbord, file, wrench (case is a little dusty and has some bar oil spilled in the bottom, but can clean up great) if anyone uses cases. I can come up with green backs if needed.

Also, got an older 041 farmboss (not AV) that I am considering parting out. Just putting a feeler out on this one.

you wanna sell the ignition?

 

[GrizzlyAdams86]

I am still in need of a decent looking top cover for an 026.

If you want it it's yours.

 

[wigglesworth]

Anybody need any MS310 parts? I picked up what's left of a parts saw the other day.

 

[wigglesworth]

If you want it it's yours.

PM sent.

 

[2000ssm6]

Anybody need any MS310 parts? I picked up what's left of a parts saw the other day.

Does it have a good p&c?

 

[wigglesworth]

Does it have a good p&c?

The piston is junk, but the cylinder cleaned up OK. It still has 2 marks in it, that I couldnt get out, but I know it should still make good compression. I do have the crank, as well as the main case, carb, carb boot, impulse, ignition coil, wires, and what's left of the top cover. It was a scrap yard pic, that somebody already robbed the clutch, oiler and chain brake parts, as well as the starter cover and flywheel.

 

[Saw Dr.]

Anybody need any MS310 parts? I picked up what's left of a parts saw the other day.

I can always use 1127 parts. I'll take the scraps nobody else needs if you want the stuff gone.

 

[2000ssm6]

The piston is junk, but the cylinder cleaned up OK. It still has 2 marks in it, that I couldnt get out, but I know it should still make good compression. I do have the crank, as well as the main case, carb, carb boot, impulse, ignition coil, wires, and what's left of the top cover. It was a scrap yard pic, that somebody already robbed the clutch, oiler and chain brake parts, as well as the starter cover and flywheel.

If Saw Dr doesn't want it, I might bite. This project won't get any attention for awhile. I really want to find a 390 p&c though. To hear they are such peices of crap, there sure isn't any floating around.:monkey:

 

[Saw Dr.]

Does it have a good p&c?

The piston is junk, but the cylinder cleaned up OK. It still has 2 marks in it, that I couldnt get out, but I know it should still make good compression. I do have the crank, as well as the main case, carb, carb boot, impulse, ignition coil, wires, and what's left of the top cover. It was a scrap yard pic, that somebody already robbed the clutch, oiler and chain brake parts, as well as the starter cover and flywheel.

Just want to point out that the only 47mm pistons are factory. There are no aftermarket MS-310 pistons. I have seen one or two OEM ones on greedbay for $75, but they're about $90 at the dealer.

 

[moparman]

Husqvarna 480 Cd parts saw

I have a 480 CD parts saw that I would like to trade for an old Pioneer or Poulan. All the castings look good except clutch cover - jumped chain cut a small hole in rear. No chainbrake parts. cylinder cover has broken right front. I have not tried to start, but was told that it will run if gas put in carb. Comes with a 20" RSN bar and Oregon 73 (.058) chain.

If interested check out photos in Tradin' Post for it.

 

[oscar4883]

Still looking for a set of 12mm 044/440 cases. Complete with crank or case halves. Either would one is great. Have a few odds and ends and a bunch of chains in good shape to trade.
Thanks
John

 

[tlandrum]

ok, now i am in need of a nice clean ms660 tank.have 044 parts and 460 parts or cash

 

[Mastermind]

I'm still needing a brake handle, the thimble that holds it, a tank vent and filter, and some other small parts for a 046. I have cash.