Swap meet...

[diggers_dad]

the last set...

So, if you have a p/c for an Echo CS 400 I would like to trade for it. Other interesting trades??

Marc

 

[o8f150]

Needing a spike for an xl12 - SXLAO.

Also a decent 16" .050 3/8 lopro bar for a Poulan wildthing type saw. My friend was wondering why his saw was cutting crooked, the bar slot was over .090

if no one has the bar,, i have 2 of them

 

[o8f150]

hey guys,,, i am needing 2-3 poulan bars 14" or less,,perfer less,, maybe 1 14" and the other short as possible,, i am out of parts to trade for now but i have a little bit of green left

 

[Tree Wacker]

hey guys,,, i am needing 2-3 poulan bars 14" or less,,perfer less,, maybe 1 14" and the other short as possible,, i am out of parts to trade for now but i have a little bit of green left

i think i might have 2 thats 14 inch but i'll have to look though.i'll send you a pm when i foind them in my messy shop LOL.

 

[o8f150]

i think i might have 2 thats 14 inch but i'll have to look though.i'll send you a pm when i foind them in my messy shop LOL.

thanks

 

[Scooterbum]

hey guys,,, i am needing 2-3 poulan bars 14" or less,,perfer less,, maybe 1 14" and the other short as possible,, i am out of parts to trade for now but i have a little bit of green left

You've got a couple bars headin' your way. Should of PM'd ya'

 

[o8f150]

You've got a couple bars headin' your way. Should of PM'd ya'

thanks,,, let me know how much

 

[stihl_collector]

I've got 2 x Husky 395xp crankcases that need crank bearings and there is a brand new 'MCW' B/B kit for 1, they both had makor top end failures. 2 good tanks 2 sets of air box's and top covers, great for someone why has the missing parts parts.

What have you got to trade me prefer stihl's projects runners etc, pm or reply here.

 

[thomas1]

You've got a couple bars headin' your way. Should of PM'd ya'

Scoot, did you get the wildthang p/c taken care of?

 

[Mo. Jim]

rings

I have a buddy looking for some 031 rings

The last one I rebuilt I used a set 041 rings 44mm. The later 028 was 44mm also, I have't miked the thickness though.

 

[Tree Sling'r]

I could use some 046/460 044/440 (12mm) pistons. OEM only. PM me, I have stuff.

 

[Jacob J.]

The last one I rebuilt I used a set 041 rings 44mm. The later 028 was 44mm also, I have't miked the thickness though.

They're both 1.5mm thick.

 

[Warped5]

Looking for a clutch-side cover for an Echo CS-280E ..

.. have stuff and green paper.

Thanks!

 

[bigblockburris]

Stihl Coil Wire

I need a coil wire for a 064/066/660.
Also in need of the wiring for the same saw.

Some Stihl parts to trade and musty green.

BBB

 

[southbound]

Needing a empty crank case for a 064..........

Also a rewind starter for 064...

I have some 034 parts and cash..

Thanks...

 

[jimbo1490]

Needing a empty crank case for a 064..........

Also a rewind starter for 064...

I have some 034 parts and cash..

Thanks...

I've got the C'case. PM Sent

 

[MEATSAW]

Looking for a 20" 3/8 bar (gauge don't matter) for my McCulloch 10-10. Would prefer sprocket nose but beggars can't be choosers. If you have one in reasonable condition let me know!

I could trade a 20" Stihl 3/8 0.063 bar in almost new condition.

 

[Tree Wacker]

Needing a spike for an xl12 - SXLAO.

Also a decent 16" .050 3/8 lopro bar for a Poulan wildthing type saw. My friend was wondering why his saw was cutting crooked, the bar slot was over .090

hey ED i looked all over my shop today and never did find the spike and the bar it's gone the sprocket is fozen up and looking like it got awful hot or something because they are a lot of discoloring on the tip of it.sorry that i couldn't help you out.

 

[stihl_collector]

I have a 041av Super cylinder here in very good condition, no piston. I also have the studs less the nuts if anyone has a 034av cylinder they would like to trade or other parts etc.

 

[MnSam]

Looking for an 038 gas tank/handle. I am willing to pay.

Bump