Swap meet...

[dh1984]

Is this the same saw that had the broken case were the handle mets? If so, how did you fix it? Are you swapping it for something?

Yes it is i just swicthed the case out that was broke and then put it back together again. right now it's not for trading or for sale unless i see something i really want and then i might have to find a other one to rebuld or something to trade .

 

[dh1984]

i need find a unlimited coil for a poulan pro 295 if their is one. got a few parts to trade but got green slips

 

[Duke Thieroff]

Anyone have a Homelite 410?


I got plenty of trade meat and stuff......



Chris

 

[parrisw]

stihl looking for an 076...
oil cap
throttle trigger
dawgs
clutch and drum,
small parts and parts saws

have CASH and other stihl parts to trade

I may be able to help with the cap and trigger. I'll try to remember to look tonight.

 

[deerjackie]

I bought a used 660 and came with 24 and 28 in bar. the 24 was used the most and i want to widen the gap a little wtt 28 for 36 or 32 b&c. The 28 has very little use on it . shoot me an e mail and i can send pics. Thanks

Found one thanks A S

 

[ChainsawmanXX]

Hey everyone looking for an adapter plate for some bars.
Need one that will convert from a 372 husky to an 066.
Got plentys to trade

 

[Metals406]

Anyone have a Homelite 410?


I got plenty of trade meat and stuff......



Chris

A runner?

 

[ChainsawmanXX]

Another list of stuff im looking for.

140 husqvarna coil
350 husky clutch, rim, clutch cover, and muffler. (Or whole parts saw)

Stihl 08 trigger and B&C
Contra- carb kit.

J-red 920 good crankcase.

 

[MechanicMatt]

Ed, I found the choke linkage to that dolmar I sent you awhile back. It was under my bench. Its freaking amazing what you find when you decide to do a thorough clean up. Ill send it along with the two caps. If you can think of any thing else you need beside the ignition and p&c off of this 031 carcass let me know before friday. .

 

[rms61moparman]

Hey everyone looking for an adapter plate for some bars.
Need one that will convert from a 372 husky to an 066.
Got plentys to trade

If you are trying to put a 372 bar on an 066 that won't work.
The Stihl studs are too big.


Mike

 

[PB]

Hey everyone looking for an adapter plate for some bars.
Need one that will convert from a 372 husky to an 066.
Got plentys to trade

I am not sure they make such a thing to go from Husky to Stihl. Husky has smaller bar studs than the stihl and a simple adapter plate won't work. Going the other way is much easier (Stihl to Husky) because all you need is a spacer.

 

[PB]

If you are trying to put a 372 bar on an 066 that won't work.
The Stihl studs are too big.


Mike

What this guy said.

 

[Arrowhead]

Ed, I found the choke linkage to that dolmar I sent you awhile back. It was under my bench. Its freaking amazing what you find when you decide to do a thorough clean up. Ill send it along with the two caps. If you can think of any thing else you need beside the ignition and p&c off of this 031 carcass let me know before friday. .

Sounds good Matt.
All I need from the 031 is the caps.

 

[woodgrenade]

Looks like I'm also in need of a 036/360 piston and cylinder. Seems that needlebearings can be quite destructive when they aren't kept in check

 

[ChainsawmanXX]

If you are trying to put a 372 bar on an 066 that won't work.
The Stihl studs are too big.


Mike

I am not sure they make such a thing to go from Husky to Stihl. Husky has smaller bar studs than the stihl and a simple adapter plate won't work. Going the other way is much easier (Stihl to Husky) because all you need is a spacer.

Thanks guys

Looks like im gonna have to open up the bar slots then!
Im new to this... husky stuff!

 

[tomdcoker]

Honestly, I do not know. I'd guess and say most likely.

They are the same. Tom

 

[Brushwacker]

Thanks guys

Looks like im gonna have to open up the bar slots then!
Im new to this... husky stuff!

I believe you could grind or file the top and bottom of the shoulder of each stud to fit the Husky bar and if you want to go back to the Stihl mount, schim the stud so the wider sides are on top and bottom.
Read it in a post here a while back.

 

[k5alive]

anyone want any 024 stuff, i have everything but a P&C, mint super top plastic, cases need bearings and seals mint as well.

 

[psuiewalsh]

Mac 310

Looking for a plastic cover plate for a Mcculloch 310 that sits on top of the carb and the choke lever runs through. The one I have snapped in half. Good news is the saw is running now though. What a PITA. I have other small Mac stuff to trade.

Also looking for a fuel filter. Anyone know something common that will fit?

 

[barneyrb]

anyone want any 024 stuff, i have everything but a P&C, mint super top plastic, cases need bearings and seals mint as well.

Shoot me a pm and tell me how much or what do you want in trade