Sagetown
Farmer and a STIHL
So, you're saying, if it was tuned to that mix ratio, you might not have that issue?
661 Oil Test 32:1 vs 40:1 vs 50:1 ?
- Thread starter redbull660
- Start date
Help Support Arborist Forum:
I run 32:1 in everything, stock and ported. It's never been an issue.
Mastermind
Work Saw Specialist
All our A/T and M/T saws run on 32:1. No drool.
Weedeaters and leafblowers too.
Weedeaters and leafblowers too.
I like that idea.
Sagetown
Farmer and a STIHL
Okay; Do you think the local Stihl Techs are capable of tuning them in for a 32:1 ratio?
KenJax Tree
Terraphobic
Which is why you guys get better gains out of say....a 346 than you do a 550, because they can be leaned out to the edge but yet stock for stock a 550 is a little stronger.
A ported 550 will nip right at the heals of a 346. I'm not saying MTronic runs rich. That was more of a question, or a possibility as to what you're seeing.
Mastermind
Work Saw Specialist
You're wasting your time young man.
More oil has been proven to make more power in tests that are far more scientific than anything you are doing here.
KenJax Tree
Terraphobic
Its possible. And i could've played with the tune on the 201T a little more but i didn't.
I would still like to see your results with the 660. Use the oil of your choice and tune to the same RPM with each mix.
We're all just guessing in the dark here. The last though I have on this, is how goofy H1R behaves, I had to open up th H speed jet on my 346 almost a full turn, when I went from running K2. I've never had to do that running any other oil. A full turn would definitely be a lot for the Mtronic system to adjust in a timely manner. IMHO this really has little if anything to do with the oil fuel ratio itself. It simply doesn't add up, and is out of line with the years of timing saw and comparing them, at gtg's or on my own time.
It would also be interesting to see how the L and H settings change on the AT and MT engines, if you use different oil ratios. But that could only be read out with the engine diagnostic tools.
Thats what Im saying. Too many variable in each cut to claim one ratio is faster than another. Proof would be a dyno.
It would be a tough to do on a dyno even.Thats what Im saying. Too many variable in each cut to claim one ratio is faster than another. Proof would be a dyno.
What does that tell you besides don't use the crap?
Yes I believe so too.
How about this for a new test... why not pick one oil at one set ratio but vary the grades of gas. Do say 40:1 of your choice and mix 89, 91, 93 and then test it against some canned fuel...?
Moparmyway
Its just a saw
- Joined
- Dec 2, 2012
- Messages
- 2,481
104Dl of RS in .404 @ .063 ................ what do you want for them ?
Yes I believe so too.
How about this for a new test... why not pick one oil at one set ratio but vary the grades of gas. Do say 40:1 of your choice and mix 89, 91, 93 and then test it against some canned fuel...?
Did that, zero difference will be noticeable without a dyno.
It tells me it effects combustion differently. H1R is far from carp. Without scientific based test, with the proper controls, this discussion and test is a bit of a cluster ****.
It tells me it inhibits combustion. I want no part of an oil that does that, as it opens up a can of worms.
And why bother with it when there are much better oils for a saw application.
And why bother with it when there are much better oils for a saw application.
