Standards for pipe thread sealant for hydraulic wood splitter

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
efiles123

efiles123

ArboristSite Lurker
Joined
Dec 29, 2023
Messages
17
Location
Northern CA
I’m currently using a Northstar 30 ton splitter that has a hydraulic fluid leak at one of the pipe fittings located under the control lever. Im looking forward to fixing the leak with some pipe thread sealant I already have but after reading the label I’m unsure if it’s suitable for this type of use. It’s rated only up to 125 degrees Fahrenheit and 125 psi. Attached are a couple pics of the sealant.
 

Attachments

  • IMG_2569.jpeg
    IMG_2569.jpeg
    1.4 MB · Views: 0
  • IMG_2568.jpeg
    IMG_2568.jpeg
    1.6 MB · Views: 0

JRM

Addicted to ArboristSite
AS Supporting Member
Joined
Jan 4, 2022
Messages
2,825
Location
Ohio
As a pipefitter by trade we are taught to use tape and dope together on all threaded pipe joints. We use Blue Monster brand tape and dope rated -50 to 400 degrees F and up to 10,000 PSI
I don't disagree with you but in reality it isn't necessary most of the time. One or the other should suffice, especially when dealing with a factory cut thread. The bigger question I'd be asking is, why is it leaking in the first place.
 
efiles123

efiles123

ArboristSite Lurker
Joined
Dec 29, 2023
Messages
17
Location
Northern CA
Here’s a pic of the elbow that’s leaking if that helps. Thinking I’ll go with something more industrial than what I have. Hopefully the auto parts store has the loctite or something similar.
 

Attachments

  • IMG_2570.jpeg
    IMG_2570.jpeg
    1.7 MB · Views: 4
Lionsfan

Lionsfan

Addicted to ArboristSite
. AS Supporting Member.
Joined
Aug 11, 2019
Messages
1,801
Location
Cheboygan, MI
That's the suction side. No pressure there. We use Talon brand pipe dope with ptfe for hydraulic, lube oil, fuel, raw water and coolant plumbing at work with good results. The exception to the rule is some of the stainless fittings we use are tough to seal and we use a couple wraps of high quality ( heavy duty yellow stuff) teflon tape on those.
 
nedsim

nedsim

ArboristSite Operative
Joined
Apr 16, 2019
Messages
176
Location
Maine
Here’s a pic of the elbow that’s leaking if that helps. Thinking I’ll go with something more industrial than what I have. Hopefully the auto parts store has the loctite or something similar.
That appears to be a return line, so low pressure. If it's not too difficult to remove the fitting and all I had on hand was the Rectorseal, I'd go ahead and give it a try. Loctite 567 is wonderful stuff, and wonderfully expensive. Just looked and the 12oz can I have here runs about $100. Even a small tube is close to $30.
 
Colonel428

Colonel428

ArboristSite Operative
Joined
Jan 29, 2022
Messages
207
Location
28105
I had a leak similar to yours and the guys at a hydraulic supply house told me to use pipe thread. Take a length of it and twist it at both ends until it becomes like a piece of string. Then wrap that down and around into the grooves of the male piece. I did it and it worked for me.
 
efiles123

efiles123

ArboristSite Lurker
Joined
Dec 29, 2023
Messages
17
Location
Northern CA
Anyone have any tips or advice for the job? Will hydraulic fluid come spilling out when I disconnect the hose? Any tricks to help-maybe tilt the splitter to one side? Have a milk jug I cut the top to catch fluid..hopefully not much comes pouring out!
 
Top