BDM53ENT
ArboristSite Operative
Looking for a couple 24"-28" bars for Homelite C series saws. Ill be running .404 063 chain. Does not have to be pretty 
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
cat-face timber
Knot Bumper
I have the following Stihl parts, want to trade for a smaller Husky project.
Each pay shipping.
Thanks.
MS460WOODCHUCK
Addicted to ArboristSite
I'm still needing a couple of poulan 306/245 air filters and a pro mac 10-10 air filter and muffler deflector with screws for the mac.
upstateny
ArboristSite Operative
Looking for a Jug for a Husky 50, Bought a piston and rings thinking i could save this jug, Doesnt look to promising. Also Looking for a Carb, intake, airfilter and cover for an Echo CS3000. The saw is grey, I dont know much about them, picked them up cheap, would just like to get them togther. Have some 181/281/288 stuff, also some older 266/272 items, and some 365/372 stuff. Green paper too!
Trying to match up a piston for Dolmar 143/153?
Now how would you have guessed that... So, come on then, out with it... What do you know???
I've compared the two before and the Husky piston is quite a bit taller- more than 1/4" taller. The wrist pin is a different size and in conjunction with the 390 piston being taller,
the skirts would end up being much higher- messing up your intake timing.
When I was looking at it I didn't really care for how much I was going to have to modify the 143/153 cylinder, so I bought an aftermarket piston from Northwood Saw when they
still had the 153 piston kit in Episan flavor.
Stihl looking for 200T parts. Little bit of everything. LOL
Sal is a good guy!
Has quite a few parts great service and reasonable shipping that is very fast.
Ok Nate, Since I have a stash.
For a 143 you will need to take a cut off the skirt. (Can't remember total, had to cut it twice)
I beveled the re-enforcement ribs a bit too.
It is domed and the last 143 I did had .050 squish! w/ gasket.
I am going to cut the base a bit, and shoot for .024 but even at .050 squish she be a bear to pull over.
Look down about 5 lines in the middle eh?
http://store.chainsawr.com/collections/chainsawr-piston-and-cylinder-kits
Has quite a few parts great service and reasonable shipping that is very fast.
Ok Nate, Since I have a stash.
For a 143 you will need to take a cut off the skirt. (Can't remember total, had to cut it twice)
I beveled the re-enforcement ribs a bit too.
It is domed and the last 143 I did had .050 squish! w/ gasket.
I am going to cut the base a bit, and shoot for .024 but even at .050 squish she be a bear to pull over.
Look down about 5 lines in the middle eh?
http://store.chainsawr.com/collections/chainsawr-piston-and-cylinder-kits
Does anyone have an 029 brake handle and air filter cover laying around? If so, I could use them.
Parts and paper to trade.
Thanks,
Bryan
Parts and paper to trade.
Thanks,
Bryan
PM sent.
kc4sfe
ArboristSite Operative
Still trying to trade a Husqvarna 455 powerhead for a Stihl powerhead project. The 455 is complete but something is keeping the piston from turning over. Cylinder looks good and no major scoring can be seen.
I'm looking for a 60cc or larger Stihl project that has a bad P/C but has all plastic and parts there.
thanks,
I'm looking for a 60cc or larger Stihl project that has a bad P/C but has all plastic and parts there.
thanks,
Scooterbum
Addicted to ArboristSite
Looking for a MS180 crankcase. Green to trade.
kc4sfe
ArboristSite Operative
Scooterbum - convo started
cat-face timber
Knot Bumper
I find my self in need of a Husky 136 carb.
What do you want in trade?
What do you want in trade?
Looking for:
1) Echo CS-900 EVL A and B Handle Assemblies
2) Clutch/ Bar and Chain Cover for Husky 268
3) Handle/Fuel tank Assembly for Stihl 044 like these but w/o the cracks or missing sections
Trade Fodder:
Husky 281xp parts saw
Poulan 4000
Green Trade Paper
Possibly something you need that I forgot to mention
Thank You,
hseII
1) Echo CS-900 EVL A and B Handle Assemblies
2) Clutch/ Bar and Chain Cover for Husky 268
3) Handle/Fuel tank Assembly for Stihl 044 like these but w/o the cracks or missing sections
Trade Fodder:
Husky 281xp parts saw
Poulan 4000
Green Trade Paper
Possibly something you need that I forgot to mention
Thank You,
hseII
Good luck ! Been trying to find good 044 tanks for a year now ! LOL Used a MS440 on one.
nmurph
ArboristSite.com Sponsor
Yep, people that have those hold onto them tightly.
I'm looking for a spark plug cover and a muffler cover for a 334/335/338XPT.
Parts and paper to trade. Thanks in advance!
Parts and paper to trade. Thanks in advance!
