Kensie1988
Vintage Saw Maniac
Was it on Craigslist? I think I saw a big Mac over that way on CL.
Vintage Chainsaw Collectors Lounge
- Thread starter Kensie1988
- Start date
Help Support Arborist Forum:
RandyMac
Stiff Member
That is probably it, not holding much hope at this point, 3 days into it, no call yet.
4 hour round trip over bad roads.
4 hour round trip over bad roads.
Kensie1988
Vintage Saw Maniac
Of course, that has to be the most frustrating thing about buying through craigslist or Facebook, then not answering.
RandyMac
Stiff Member
Not a 700D, I do have a couple hours with my 600D, pulls better than you would think, nice balance, fair amount of vibes, very loud.
I converted to a rim sprocket, running 3/8th on a roller nose.
I converted to a rim sprocket, running 3/8th on a roller nose.
Mac&Homelite
Addicted to ArboristSite
Boomer is on a roll of collecting saws I see... meanwhile I'm not adding to the collection which is just fine for me. 
Too many saws that don't currently run, and time and funds to fix them are limited. Also what does everyone use for crankcase splitters? I need one to do my next couple project saws unfortunately.
Too many saws that don't currently run, and time and funds to fix them are limited. Also what does everyone use for crankcase splitters? I need one to do my next couple project saws unfortunately.
Kensie1988
Vintage Saw Maniac
You need to be faster! I'm going up to Hot Springs Arkansas this weekend, I hope I can at least see some cool stuff while I'm there. I don't have to buy anything, I just like the conversation lol
RandyMac
Stiff Member
I picked up some trade fodder for the GTG.
075, 36'' roller
075, 36'' roller
Kensie1988
Vintage Saw Maniac
That's sweet!
RandyMac
Stiff Member
I need fence boards far more than the 075. Pulls over nice, lots of compression, tried to start, but decomp button pops out and pulled the handle through my fingers.
It does has a hole top front of recoil housing. It doesn't look like it has been fussed with.
It does has a hole top front of recoil housing. It doesn't look like it has been fussed with.
Attachments
Have a safe trip and don't buy it unless you got to have it cause your life depends on it.
Steve
I hate collecting, always got to have it.
Steve
Steve
Kensie1988
Vintage Saw Maniac
Thanks, didn't see much up here. I did pick up a new knife though, Ken Onion design for Ruger/CRKT knives, the clip point is really what attracted me to this knife.
brandonstc6
Addicted to ArboristSite
This weekend I picked up 4 saws for $45
Stihl 025
Stihl 031
Pioneer 1074
Mini Mac 35
I also got a welder and a very old (1960s) variable voltage battery charger for $20 for both.
Sent from my iPhone using Tapatalk
Stihl 025
Stihl 031
Pioneer 1074
Mini Mac 35
I also got a welder and a very old (1960s) variable voltage battery charger for $20 for both.
Sent from my iPhone using Tapatalk
Got my 5200 going, took awhile to get the carb set, that was a pain with that compression. Also worked on a mighty mite, quick 5 minutes of work. Guy picked it up for $10.00 and couldn't start it. I added fuel and oil, dribbled a little gas in the carb and fired on third pull. Good running little saw, started on 1/4 pull when warm.
Steve
Steve
Son in law says that poulan has a mean lick at idle. [emoji38]
Steve
Steve
